Cisco Wireless Controller 5508 Configuration Step by Step – Part 1 (CLI and GUI Access, Upgrade)
As the industry’s most deployed controller, the Cisco 5500 Series Wireless Controller provides the highest performance, security, and scalability to support business communications today and in the future.
Cisco 5500 Series Wireless Controller
??Support for up to 500 access points and 7000 clients
? 8-Gbps throughput, eight 1 Gigabit Ethernet ports, with Link Aggregation Group (LAG)
support
? Standalone, rack-mountable appliance
| 5508 Front Panel |
Relate Posts:
- Cisco Wireless Controller 5508 Configuration Step by Step – Part 1 (CLI and GUI)?–
- Cisco Wireless Controller 5508 Configuration Step by Step – Part 2 (User/Machine Auth)?–
- Cisco Wireless Controller 5508 Configuration Step by Step – Part 3 (Certs Auth and Other Settings)
Benefits include:
? Seamless, high-quality mobile experience: Efficient roaming capabilities help ensure consistent experience on any smart mobile device with voice and video applications.
? Reliability: Cisco 5500 Series Wireless Controllers provide industry-leading IPv6 roaming with secure access.
? Flexibility to pay as you grow: The Cisco 5500 Series offers software license flexibility to add additional access points as business requirements change.
? Versatility: Supports advanced services for any network use case, campus or branch, including Cisco OfficeExtend solutions for secure mobile teleworking and Cisco Enterprise Wireless Mesh solutions, which allow access points to dynamically establish wireless connections in hard-to-connect locations.
1. Booting Terminal Outputs:
| WLCNG Boot Loader Version 1.0.20 (Built on Jan ?9 2014 at 19:02:44 by cisco) Board Revision 1.3 (SN: FCW2016B091, Type: AIR-CT5508-K9) (G) Verifying boot loader integrity… OK. OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate) FPGA Revision 1.7 Env FW Revision 1.8 USB Console Revision 2.2 CPU Cores: ?10 DRAM: ?1024 MB Flash: 32 MB Clearing DRAM…….. done Network: octeth0′, octeth1 ? ‘ – Active interface ? E – Environment MAC address override CF Bus 0 (IDE): OK? IDE device 0: ?– Model: SGEFD1GHB9P1D221 Firm: FW981 Ser#: STP194512FP ?– Type: Hard Disk ?– Capacity: 977.4 MB = 0.9 GB (2001888 x 512) Press <ESC> now to access the Boot Menu… Loading primary image (7.4.121.0) 100%? 34583665 bytes read Launching… init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary starting pid 840, tty ”: ‘/etc/init.d/rcS’ Set PLX switch MPS settings ………….!!!!!!! Detecting Hardware … set smp_affinity for irq 48 003f DP from CGE5.0 … starting pid 1086, tty ‘/dev/ttyS0’: ‘/usr/bin/gettyOrMwar’ Setting up ZVM Exporting LD_LIBRARY_PATH Cryptographic library self-test….passed! XML config selected Validating XML configuration octeon_device_init: found 1 DPs readCPUConfigData: cardid 0x6070001 Cisco is a trademark of Cisco Systems, Inc. Software Copyright Cisco Systems, Inc. All rights reserved. Cisco AireOS Version 7.4.121.0 Firmware Version FPGA 1.7, Env 1.8, USB console 2.2 Initializing OS Services: ok Initializing Serial Services: ok Initializing Network Services: ok Initializing Licensing Services: ok License daemon start initialization….. License daemon running….. Starting Statistics Service: ok Starting ARP Services: ok Starting Trap Manager: ok Starting Network Interface Management Services: ok Starting System Services: ok Starting FIPS Features: ok : Not enabled Starting Fastpath Hardware Acceleration: ok Starting Fastpath Console redirect : ok Starting Fastpath DP Heartbeat : ok Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok Fastpath CPU0.00: Initializing last packet received queue. Num of cores(10) Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040 Fastpath CPU0.00: Core 0 Initialization and FIPS self-test: ok Fastpath CPU0.00: Initializing Timer… Fastpath CPU0.00: Initializing Timer…done. Fastpath CPU0.00: Initializing Timer… Fastpath CPU0.00: Initializing NBAR AGING Timer…done. Fastpath CPU0.01: Core 1 Initialization and FIPS self-test: ok Fastpath CPU0.02: Core 2 Initialization and FIPS self-test: ok Fastpath CPU0.03: Core 3 Initialization and FIPS self-test: ok Fastpath CPU0.03: Received instruction to get link status Fastpath CPU0.04: Core 4 Initialization and FIPS self-test: ok Fastpath CPU0.05: Core 5 Initialization and FIPS self-test: ok Fastpath CPU0.06: Core 6 Initialization and FIPS self-test: ok Fastpath CPU0.07: Core 7 Initialization and FIPS self-test: ok Fastpath CPU0.08: Core 8 Initialization and FIPS self-test: ok Fastpath CPU0.09: Core 9 Initialization and FIPS self-test: ok Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting Redundancy: ok? Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok? Starting Security Services: ok Starting Policy Manager: ok Starting Authentication Engine: ok Starting Mobility Management: ok Starting AVC Services: ok Starting Virtual AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature Manager: ok Starting RFID Tag Tracking: ok Starting RF Profiles: ok Starting Power Supply and Fan Status Monitoring Service: ok Starting Mesh Services: ?ok Starting TSM: ok Starting CIDS Services: ok Starting Ethernet-over-IP: ok Starting DTLS server: ?enabled in CAPWAP Starting CleanAir: ok Starting WIPS: ok? Starting SSHPM LSC PROV LIST: ok? Starting RRC Services: ok Starting SXP Services: ok Starting Alarm Services: ok Starting FMC HS: ok? Starting IPv6 Services: ok Starting Config Sync Manager : ok Starting Hotspot Services: ok Starting PMIP Services: ok Starting Portal Server Services: ok Starting mDNS Services: ok Starting Management Services:? ? ?Web Server: ? ?CLI: ok ? ?Secure Web: ok ? ?License Agent: ok (Cisco Controller)? Enter User Name (or ‘Recover-Config’ this one-time only to reset configuration to factory defaults) User: ?admin Password:********** (Cisco Controller) > |
2. Basic CLI Commands:
| (Cisco Controller) >show ? ? ? ? ? ? ? ? ? 802.11a ? ? ? ?Display 802.11a configuration. 802.11b ? ? ? ?Display 802.11b configuration. 802.11h ? ? ? ?Display 802.11h configuration. aaa ? ? ? ? ? ?Displays AAA related information acl ? ? ? ? ? ?Display system Access Control Lists. advanced ? ? ? Display Advanced configuration and statistics. ap ? ? ? ? ? ? Display AP Configuration. arp ? ? ? ? ? ?Display ARP cache. assisted-roaming Display Assisted Roaming and 802.11k configuration. auth-list ? ? ?Display AP authorization list. avc ? ? ? ? ? ?Display AVC Configuration/Statistics. band-select ? ?Display Aggressive Load Balancing configuration. boot ? ? ? ? ? Displays the default boot image. buffers ? ? ? ?Display pmalloc buffer utilization. cac ? ? ? ? ? ?Show Call-Admission-Control details call-control ? Display Call-control information cdp ? ? ? ? ? ?Display CDP information certificate ? ?Display SSL Certificate Configuration. client ? ? ? ? Displays active clients. coredump ? ? ? Displays Core Dump Summary country ? ? ? ?Display the configured countries. –More– or (q)uit cpu ? ? ? ? ? ?Display current CPU usage information. cts ? ? ? ? ? ?Displays CTS Information? custom-web ? ? Display Web Authentication customization information. database ? ? ? Show local database configuration. debug ? ? ? ? ?Display enabled debugs. dhcp ? ? ? ? ? Display the dhcp server configuration. dtls ? ? ? ? ? Display the DTLS server status. eventlog ? ? ? Display event log entries. exclusionlist ?Display exclusion-list. flexconnect ? ?Display controller flexconnect information. flow ? ? ? ? ? Display flow Configuration. guest-lan ? ? ?Display Guest LAN Configuration. ike ? ? ? ? ? ?Display active IKE SAs. interface ? ? ?Display system interfaces. invalid-config Display Invalid Config. inventory ? ? ?Display vital product data. ipsec ? ? ? ? ?Display active IPSEC SAs. ipv6 ? ? ? ? ? Display IPv6 information. lag ? ? ? ? ? ?Display Link Aggregation Group (LAG) information. ldap ? ? ? ? ? Displays LDAP information. license ? ? ? ?Displays License related information. linktest ? ? ? Shows the configured frame size and number of frames for linktest. load-balancing Display Aggressive Load Balancing configuration. –More– or (q)uit local-auth ? ? Display Local EAP Authentication information. location ? ? ? Display Location based System information logging ? ? ? ?Display logger parameters and buffer contents. loginsession ? Display login session info. macfilter ? ? ?Display MAC filtering configuration. mdns ? ? ? ? ? Displays mDNS information media-stream ? Display Multicast-direct Configuration State memory ? ? ? ? Display system memory usage statistics. mesh ? ? ? ? ? Show mesh configuration. mgmtuser ? ? ? Display local management user accounts. mobility ? ? ? Display Mobility Management Configuration. msglog ? ? ? ? Display message log entries. netuser ? ? ? ?Display local network user accounts. network ? ? ? ?Display configuration for inband connectivity. nmheartbeat ? ?Displays Network Manager Heart Beat Summary nmsp ? ? ? ? ? Displays data for NMSP protocol between controller and Location Server. ntp-keys ? ? ? Display the system time. pmipv6 ? ? ? ? Proxy mobility pmk-cache ? ? ?Display information about the PMK cache. port ? ? ? ? ? Display port mode and settings; display port status. process ? ? ? ?Display CPU and memory usage per process. qos ? ? ? ? ? ?Display qos information (queue length) queue-info ? ? Display system Message Queue Information. –More– or (q)uit radius ? ? ? ? Displays RADIUS information. redundancy ? ? Display redundancy information. remote-lan ? ? Display remote LAN Configuration. reset ? ? ? ? ?Display scheduled system reset parameters. rf-profile ? ? Configures RF Profile parameters. rfid ? ? ? ? ? Shows the RFID tag tracking information rogue ? ? ? ? ?Displays Rogue AP and Client information. route ? ? ? ? ?Display configured route rules ? ? ? ? ?Display active internal firewall rules. run-config ? ? Display running configuration. running-config Display running configuration. serial ? ? ? ? Display EIA-232 parameters and serial port inactivity timeout. service ? ? ? ?Display service information. sessions ? ? ? Display cli session configuration information. snmpcommunity ?Display SNMP community entries. snmpengineID ? Display SNMP v3 EngineId. snmptrap ? ? ? Display SNMP trap port number and trap receiver entries. snmpv3user ? ? Display SNMP v3 user entries. snmpversion ? ?Display SNMP v1/v2/v3c status(enabled or disabled). stats ? ? ? ? ?Display port and switch statistics. switchconfig ? Display parameters that apply to the switch. sysinfo ? ? ? ?Display system information including system up time. syslog ? ? ? ? Displays the state of system syslog. –More– or (q)uit tacacs ? ? ? ? Displays TACACS+ information. tech-support ? Display system resource information. time ? ? ? ? ? Display the system time. trapflags ? ? ?Display the value of trap flags that apply to the switch. traplog ? ? ? ?Display trap records. udi ? ? ? ? ? ?Display UDI for the controller wgb ? ? ? ? ? ?Displays active work-group bridges (WGB). wlan ? ? ? ? ? Display WLAN Configuration. wps ? ? ? ? ? ?Displays WPS Configuration. ? ? ? ? ? ? ? ? (Cisco Controller) >? ? ? ? ? ? ? ? ? ? ? clear ? ? ? ? ?Clear selected configuration elements. config ? ? ? ? Configure switch options and settings. debug ? ? ? ? ?Manages system debug options. eping ? ? ? ? ?Send Ethernet-over-IP echo packets to a specified mobility peer IP address. help ? ? ? ? ? Help license ? ? ? ?Manage Software License linktest ? ? ? Perform a link test to a specified MAC address. logout ? ? ? ? Exit this session. Any unsaved changes are lost. mping ? ? ? ? ?Send Mobility echo packets to a specified mobility peer IP address. ping ? ? ? ? ? Send ICMP echo packets to a specified IP address. reset ? ? ? ? ?Reset options. save ? ? ? ? ? Save switch configurations. show ? ? ? ? ? Display switch options and settings. test ? ? ? ? ? Test trigger commands transfer ? ? ? Transfer a file to or from the switch. ? ? ? ? ? ? ? ? (Cisco Controller) > PID: AIR-CT5508-K9, ?VID: V04, ?SN: FCW2016B091 |
WLC 5508 ?will use a startup wizard to guide you for basic configuration.?Cisco 5508 Wireless Controller Installation Guide?gives more details on each step.
3. Configure SP (Service Port)
?
Service Port is used exclusively for Out-of-Band management. It is the only port that is active when the controller is in boot mode (useful for troubleshooting). The service port does not support 802.1Q tagging so you must configure the switch port on the other side in access mode. It does not support a backup port and a default gateway in its configuration. This last fact means that you can reach it only if you are on the same subnet (as it will not have a route back) unless you configure static routes in the menu Controller -> Network Routes.
***The service port and the management interface must be on a different subnet.The service port is also not auto-sensing so you must use the correct straight-through or crossover Ethernet cable to communicate with the service port
| (Cisco Controller) >show interface summary? ?Number of Interfaces…………………….. 5 Interface Name ? ? ? ? ? ? ? ? ? Port Vlan Id ?IP Address ? ? ?Type ? ?Ap Mgr Guest ——————————– —- ——– ————— ——- —— —– management ? ? ? ? ? ? ? ? ? ? ? 1 ? ?untagged 10.9.0.30 ? ?Static ?Yes ? ?No ?? redundancy-management ? ? ? ? ? 1 ? ?untagged 0.0.0.0 ? ? ? ? Static ?No ? ? No ?? redundancy-port ? ? ? ? ? ? ? ? ?– ? ?untagged 0.0.0.0 ? ? ? ? Static ?No ? ? No ?? service-port ? ? ? ? ? ? ? ? ? ? N/A ?N/A ? ? ?0.0.0.0 ? ? ? ? DHCP ? ?No ? ? No ?? virtual ? ? ? ? ? ? ? ? ? ? ? ? ?N/A ?N/A ? ? ?10.4.1.1 ? ? ?Static ?No ? ? No ?? (Cisco Controller) config>interface ? ? ? ? ? ? ? ? ? acl ? ? ? ? ? ?Configures an interface’s Access Control List. address ? ? ? ?Configures an interface’s address information. ap-manager ? ? Disables AP Manager features on a dynamic interface. create ? ? ? ? Adds a new dynamic interface. delete ? ? ? ? Deletes a dynamic interface. dhcp ? ? ? ? ? Configures DHCP options on an interface. group ? ? ? ? ?Configures an interface group’s information guest-lan ? ? ?Configure Guest LAN vlan hostname ? ? ? Configures the virtual interface’s virtual DNS host name. mdns-profile ? Configures mDNS profile for the interface nasid ? ? ? ? ?Configures NAS-identifier for the interface. nat-address ? ?Configures an interface’s NAT address information. port ? ? ? ? ? Assign interface to physical port. quarantine ? ? Configure quarantine vlan vlan ? ? ? ? ? Configures an interface’s VLAN Identifier. ? ? ? ? ? ? ? ? (Cisco Controller) config>interface address ? ? ? ? ? ? ? ? ? dynamic-interface Enter interface name. management ? ? Configures the management interface. redundancy-management Configures redundancy management interface (required for redundancy). service-port ? Configures the out-of-band service Port. virtual ? ? ? ?Configures the virtual gateway interface. ? ? ? ? ? ? ? ? (Cisco Controller) config>interface address management 10.9.9.99 ? ? ? ? ? ? ? ? ? <netmask> ? ? ?Enter the interface’s netmask. ? ? ? ? ? ? ? ? (Cisco Controller) config>interface address management 10.9.9.99 255.255.255.0 Incorrect input! Use ‘config interface address management <addr> <netmask> <gateway>’ (Cisco Controller) config>interface address management 10.9.9.99 255.255.255.0 10.9.9.1 Request failed – Active WLAN using interface. Disable WLAN first. (Cisco Controller) config>exit ? ? ? ? ? ? (Cisco Controller) >config wlan disable Incorrect input! Use ‘config wlan [enable/disable] [<WLAN id> | all]’ (Cisco Controller) >config wlan disable all (Cisco Controller) >config (Cisco Controller) config>interface address management 10.9.9.99 255.255.255.0 10.9.9.1 (Cisco Controller) config> (Cisco Controller) config>interface address service-port 10.9.20.30 255.255.255.0 The DHCP protocol for the service port must be disabled before configuring the IP addr (Cisco Controller) config>interface dhcp service-port disable? (Cisco Controller) config>interface address service-port 10.9.20.30 255.255.255.0 (Cisco Controller) config>exit (Cisco Controller) >save config Are you sure you want to save? (y/n) y Configuration Saved! (Cisco Controller) > (Cisco Controller) >show interface detailed service-port? Interface Name…………………………….. service-port MAC Address……………………………….. 04:62:73:7b:73:e1 IP Address………………………………… 10.9.20.30 IP Netmask………………………………… 255.255.255.0 DHCP Protocol……………………………… Disabled AP Manager………………………………… No Guest Interface……………………………. No (Cisco Controller) > |
?
The management interface is the default interface for in-band management of the controller and connectivity to enterprise services such as AAA servers. It is also used for communications between the controller and access points. The management interface has the only consistently “pingable” in-band interface IP address on the controller.?
After connecting SP (Service Port) within your laptop network, you will be able to browse the web page of your WLC.
?
RP port is Redundancy Port.?After the WLCs are configured with Redundancy Management and Peer Redundancy Management IP Addresses and Redundant Units are configured, it is time to enable SSO. It is important to make sure that physical connections are up between both the controllers (that is, both the WLCs are connected back to back via the Redundant Port using an Ethernet cable) and the uplink is also connected to the infrastructure switch and the gateway is reachable from both the WLCs before SSO is enabled. Once SSO is enabled, it will reboot the WLCs. While it boots, the WLCs negotiate the HA role as per the configuration via Redundant Port. If the WLCs cannot reach each other via Redundant Port or via the Redundant Management Interface, the WLC configured as Secondary may go in to Maintenance Mode.
5. Upgrade 5508 IOS
Once the WLC is upgraded, it must be rebooted for the changes to take effect. Within this time, connectivity to the WLC is lost. LAPs registered to a WLC lose their association to the WLC, so service to the wireless clients is interrupted. When you upgrade the controller’s software, the software on the controller’s associated access points is also automatically upgraded.
When an access point loads software, each of its LEDs blinks in succession. Up to 10 access points can be concurrently upgraded from the controller. Do not power down the controller or any access point during this process; otherwise, you might corrupt the software image.
Cisco WLC 5508 has latest recommended version 8.0.133.0 from?this url. I was able to get?AIR-CT5500-K9-8-0-121-0.aes from?Baidu Cloud. The size is about 165Mb.?
Note: latest suggested version is 8.0.140 from Cisco download software website.?
?
There are more details regarding upgrading 5508 IOS to latest one from CCIEROO.COM’s?post. You will just need?a TFTP server on your network that is reachable from the management IP address of the WLC.
It will only take a couple of minutes to download 8.0.121.0 package from TFTP server to WLC controller based on your connection speed, but for WLC5508 to process new IOS package it took almost 20 minutes.
Until 5508 completed processing new 8.0.121 IOS, you will see the Primary Image will change to 8.0.121.0 from Config Boot page.
Note: download software from?8.0.140 and 8.2.150
Reference:
1.?Cisco 5508 Wireless Controller Installation Guide
2.?Cisco 5508 WLC Setup and Initial Configuration
3.?Step by Step guide to build a Cisco wireless infrastructure using Cisco WLC 5500, Cisco 1142 AP and Microsoft Radius server
4.?亁頤堂現任明教教主融合網絡CCNA.第一天.融合網絡概述.1
5.?Wireless LAN Controller (WLC) Software Upgrade
Share this:
- More
Like this:
Like Loading...Related
總結
以上是生活随笔為你收集整理的Cisco Wireless Controller 5508 Configuration Step by Step – Part 1 (CLI and GUI Access, Upgrade)的全部內容，希望文章能夠幫你解決所遇到的問題。
- 上一篇： 小米2023年安卓之光！小米13 Ult
- 下一篇： 信用贷款额度是怎么确定的？