上個ensp實驗只發了配置，這次是命令條目

• 前言
• 一、實驗及需求
• 二、命令
• • 1、R1
  • 2、R2
  • 3、R3
  • 4、R4
  • 5、LSW1
  • 6、LSW2
  • 7、LSW3
• 三、需求5的結果
• 總結

---

前言

上次沒來的及法命令條目，只來得及發了配置，今天補上

一、實驗及需求

要求按照拓撲圖配置相關命令使得圖中所有終端能夠網絡互通。
（1）MSTP+鏈路聚合：在SW1和SW2之間配置鏈路聚合，要求正常情況下有2條鏈路活躍、一條鏈路備份。常情況下各VLAN流量路徑要求：VLAN10:SW3->SW2->R1；VLAN20:SW3->SW1->R1
（2）VRRP：正常情況下要求VLAN10的Master為SW2；VLAN20的Master為SW1
（3）DHCP：R3為DHCP中繼代理，R2為DHCP服務器，為PC4、PC5提供動態分配IP服務。
（4）按照拓撲圖中的要求在各三層交換機和路由器上配置路由，使得所有PC終端能夠網絡互通(10分)。
（5）NAT：使用EasyIp進行轉換使得Client1能夠使用R1的外網口IP訪問外網；并使用NAT-Server使得Client1訪問Server1的web服務時能夠使用目標網址23.0.0.3/24的8080端口進行訪問

二、命令

1、R1

<Huawei>undo terminal monitor Info: Current terminal monitor is off. <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]user-interface console 0 [Huawei-ui-console0]idle-timeout 0 0 [Huawei-ui-console0]q [Huawei]int g0/0/0 [Huawei-GigabitEthernet0/0/0]ip add 10.0.0.1 24 [Huawei-GigabitEthernet0/0/0]int g0/0/1 [Huawei-GigabitEthernet0/0/1]ip add 11.0.0.1 24 [Huawei-GigabitEthernet0/0/1]int g0/0/2 [Huawei-GigabitEthernet0/0/2]ip add 12.0.0.1 24 [Huawei-GigabitEthernet0/0/2]q [Huawei]ospf [Huawei-ospf-1]area 0 [Huawei-ospf-1-area-0.0.0.0]net 10.0.0.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]net 11.0.0.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]net 12.0.0.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]q [Huawei-ospf-1]q [Huawei]acl number 3000 [Huawei-acl-adv-3000] rule 5 permit ip source 192.168.10.0 0.0.0.255 [Huawei-acl-adv-3000]int g0/0/2 [Huawei-GigabitEthernet0/0/2]nat outbound 3000

2、R2

<Huawei>undo terminal monitor Info: Current terminal monitor is off. <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]user-interface console 0 [Huawei-ui-console0]idle-timeout 0 0 [Huawei-ui-console0]int g0/0/0 [Huawei-GigabitEthernet0/0/0]ip add 12.0.0.2 24 [Huawei-GigabitEthernet0/0/0]int g0/0/1 [Huawei-GigabitEthernet0/0/1]ip add 23.0.0.2 24 [Huawei-GigabitEthernet0/0/1]int g0/0/2 [Huawei-GigabitEthernet0/0/2]ip add 24.0.0.2 24 [Huawei-GigabitEthernet0/0/2]q [Huawei]ospf [Huawei-ospf-1]area 0 [Huawei-ospf-1-area-0.0.0.0]net 12.0.0.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]q [Huawei-ospf-1]import-route rip 1 type 1 cost 1 [Huawei-ospf-1]default-route-advertise always [Huawei-ospf-1]import-route static [Huawei-ospf-1]q [Huawei]rip 1 [Huawei-rip-1]v 2 [Huawei-rip-1]undo summary [Huawei-rip-1]net 23.0.0.0 [Huawei-rip-1]import-route ospf 1 cost 14 [Huawei-rip-1]default-route originate [Huawei-rip-1]q [Huawei]dhcp enable Info: The operation may take a few seconds. Please wait for a moment.done. [Huawei]ip pool 1 Info: It's successful to create an IP address pool. [Huawei-ip-pool-1]gateway-list 192.168.40.1 [Huawei-ip-pool-1]net 192.168.40.0 mask 255.255.255.0 [Huawei-ip-pool-1]dns-list 8.8.8.8 [Huawei-ip-pool-1]lease day 10 [Huawei-ip-pool-1]int g0/0/1 [Huawei-GigabitEthernet0/0/1]dhcp select glo [Huawei-GigabitEthernet0/0/1]q [Huawei]ip route-static 192.168.30.0 24 24.0.0.4 [Huawei]ip route-static 192.168.40.0 24 23.0.0.1

3、R3

<Huawei>undo terminal monitor Info: Current terminal monitor is off. <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]user-interface console 0 [Huawei-ui-console0]idle-timeout 0 0 [Huawei-ui-console0]int g0/0/0 [Huawei-GigabitEthernet0/0/0]ip add 23.0.0.1 24 [Huawei-GigabitEthernet0/0/0]int g0/0/1 [Huawei-GigabitEthernet0/0/1]ip add 192.168.40.1 24 [Huawei-GigabitEthernet0/0/1]int g0/0/2 [Huawei-GigabitEthernet0/0/2]ip add 192.168.50.1 24 [Huawei-GigabitEthernet0/0/2]q [Huawei]rip [Huawei-rip-1]version 2 [Huawei-rip-1]undo summary [Huawei-rip-1]net 23.0.0.0 [Huawei-rip-1]net 192.168.40.0 [Huawei-rip-1]net 192.168.50.0 [Huawei-rip-1]default-route originate [Huawei-rip-1]q [Huawei]dhcp enable Info: The operation may take a few seconds. Please wait for a moment.done. [Huawei]int g0/0/1 [Huawei-GigabitEthernet0/0/1]dhcp select relay [Huawei-GigabitEthernet0/0/1]dhcp relay server-ip 23.0.0.2 [Huawei-GigabitEthernet0/0/1]q [Huawei]int g0/0/0 [Huawei-GigabitEthernet0/0/0] nat server protocol tcp global 23.0.0.3 8080 insid e 192.168.50.100 www

4、R4

<Huawei>undo terminal monitor Info: Current terminal monitor is off. <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]user-interface console 0 [Huawei-ui-console0]idle-timeout 0 0 [Huawei-ui-console0]int g0/0/0 [Huawei-GigabitEthernet0/0/0]ip add 192.168.30.1 24 [Huawei-GigabitEthernet0/0/0]int g0/0/2 [Huawei-GigabitEthernet0/0/2]ip add 24.0.0.4 24 [Huawei-GigabitEthernet0/0/2]q [Huawei]ip route-static 0.0.0.0 0 24.0.0.2

5、LSW1

<Huawei>undo terminal monitor Info: Current terminal monitor is off. <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]user-interface console 0 [Huawei-ui-console0]idle-timeout 0 0 [Huawei-ui-console0]q [Huawei]vlan bat 10 20 100 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei]int g0/0/1 [Huawei-GigabitEthernet0/0/1]port link-type access [Huawei-GigabitEthernet0/0/1]port default vlan20 [Huawei-GigabitEthernet0/0/1]int g0/0/5 [Huawei-GigabitEthernet0/0/5]port link-type access [Huawei-GigabitEthernet0/0/5]port default vlan 20 [Huawei-GigabitEthernet0/0/5]q [Huawei]stp mode mstp [Huawei]stp region-configuration [Huawei-mst-region]region-name huawei [Huawei-mst-region]revision-level 1 [Huawei-mst-region]instance 1 vlan 10 [Huawei-mst-region]instance 2 vlan 20 [Huawei-mst-region]active region-configuration Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-mst-region]q [Huawei]stp instance 2 root primary [Huawei]stp instance 1 root secondary [Huawei]int vlan 20 [Huawei-Vlanif20]vrrp vrid 20 virtual-ip 192.168.20.1 [Huawei-Vlanif20]vrrp vrid 20 priority 105 [Huawei-Vlanif20]vrrp vrid 20 track int g0/0/5 [Huawei-Vlanif20]int vlan 10 [Huawei-Vlanif10]vrrp vrid 10 virtual-ip 192.168.10.1 [Huawei-Vlanif10]q [Huawei]int vlan 20 [Huawei-Vlanif20]ip add 192.168.20.10 24 [Huawei-Vlanif20]int vlan 10 [Huawei-Vlanif10]ip add 192.168.10.10 24 [Huawei-Vlanif10]int vlan 100 [Huawei-Vlanif100]ip add 10.0.0.10 24 [Huawei-Vlanif100]q [Huawei]lacp priority 1000 [Huawei]int Eth-Trunk1 [Huawei-Eth-Trunk1]bpdu enable [Huawei-Eth-Trunk1]mode lacp-static [Huawei-Eth-Trunk1]q [Huawei]int g0/0/2 [Huawei-GigabitEthernet0/0/2]eth-trunk 1 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-GigabitEthernet0/0/2]int g0/0/3 [Huawei-GigabitEthernet0/0/3]eth-trunk 1 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-GigabitEthernet0/0/3]int g0/0/4 [Huawei-GigabitEthernet0/0/4]eth-trunk 1 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-GigabitEthernet0/0/4]int eth-trunk 1 [Huawei-Eth-Trunk1]max active-linknumber 2 [Huawei-Eth-Trunk1]port link-type trunk [Huawei-Eth-Trunk1]port trunk allow-pass vlan all [Huawei-Eth-Trunk1]q [Huawei]ospf [Huawei-ospf-1]area 0 [Huawei-ospf-1-area-0.0.0.0]net 10.0.0.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]net 192.168.10.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]net 192.168.20.0 0.0.0.255

6、LSW2

<Huawei>undo terminal monitor Info: Current terminal monitor is off. <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]user-interface console 0 [Huawei-ui-console0]idle-timeout 0 0 [Huawei-ui-console0]q [Huawei]vlan bat 10 20 100 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei]int g0/0/1 [Huawei-GigabitEthernet0/0/1]port link-type access [Huawei-GigabitEthernet0/0/1]port default vlan 10 [Huawei-GigabitEthernet0/0/1]int g0/0/5 [Huawei-GigabitEthernet0/0/5]port link-type access [Huawei-GigabitEthernet0/0/5]port default vlan 100 [Huawei-GigabitEthernet0/0/5]q [Huawei]stp mode mstp [Huawei]stp region-configuration [Huawei-mst-region]region-name huawei [Huawei-mst-region]revision-level 1 [Huawei-mst-region]instance 1 vlan 10 [Huawei-mst-region]instance 2 vlan 20 [Huawei-mst-region]active region-configuration Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-mst-region]q [Huawei]stp instance 1 root primary [Huawei]stp instance 2 root secondary [Huawei]int vlan 10 [Huawei-Vlanif10]vrrp vrid 10 vir 192.168.10.1 [Huawei-Vlanif10]vrrp vrid 10 pri 105 [Huawei-Vlanif10]vrrp vrid 10 track int g0/0/5 [Huawei-Vlanif10]int vlan 20 [Huawei-Vlanif20]vrrp vrid 20 vir 192.168.20.1 [Huawei-Vlanif20]q [Huawei]int vlan 10 [Huawei-Vlanif10]ip add 192.168.10.20 24 [Huawei-Vlanif10]int vlan 20 [Huawei-Vlanif20]ip add 192.168.20.20 24 [Huawei-Vlanif20]int vlan 100 [Huawei-Vlanif100]ip add 11.0.0.20 24 [Huawei-Vlanif100]q [Huawei]lacp pri 1000 [Huawei]int eth-tr 1 [Huawei-Eth-Trunk1]bpdu enable [Huawei-Eth-Trunk1]mode lacp-static [Huawei-Eth-Trunk1]q [Huawei]int g0/0/2 [Huawei-GigabitEthernet0/0/2]eth-tr 1 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-GigabitEthernet0/0/2]int g0/0/3 [Huawei-GigabitEthernet0/0/3]eth-tr 1 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-GigabitEthernet0/0/3]int g0/0/4 [Huawei-GigabitEthernet0/0/4]eth-tr 1 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei-GigabitEthernet0/0/4]q [Huawei]int eth-trunk 1 [Huawei-Eth-Trunk1]max active-linknumber 2 [Huawei-Eth-Trunk1]port link-type trunk [Huawei-Eth-Trunk1]port trunk allow-pass vlan all [Huawei-Eth-Trunk1]q [Huawei]ospf [Huawei-ospf-1]area 0 [Huawei-ospf-1-area-0.0.0.0]net 11.0.0.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]net 192.168.10.0 0.0.0.255 [Huawei-ospf-1-area-0.0.0.0]net 192.168.20.0 0.0.0.255

7、LSW3

<Huawei>undo terminal monitor Info: Current terminal monitor is off. <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]user-interface console 0 [Huawei-ui-console0]idle-timeout 0 0 [Huawei-ui-console0]q [Huawei]vlan bat 10 20 Info: This operation may take a few seconds. Please wait for a moment...done. [Huawei]int e0/0/1 [Huawei-Ethernet0/0/1]port link-type access [Huawei-Ethernet0/0/1]port default vlan 10 [Huawei-Ethernet0/0/1]int e0/0/2 [Huawei-Ethernet0/0/2]port link-type access [Huawei-Ethernet0/0/2]port default vlan 20 [Huawei-Ethernet0/0/2]int e0/0/3 [Huawei-Ethernet0/0/3]port link-type access [Huawei-Ethernet0/0/3]port default vlan 10 [Huawei-Ethernet0/0/3]int g0/0/1 [Huawei-GigabitEthernet0/0/1]port link-type access [Huawei-GigabitEthernet0/0/1]port default vlan 20 [Huawei-GigabitEthernet0/0/1]int g0/0/2 [Huawei-GigabitEthernet0/0/2]port link-type access [Huawei-GigabitEthernet0/0/2]port default vlan 10 [Huawei-GigabitEthernet0/0/2]q [Huawei]stp mode mstp [Huawei]stp region-configuration [Huawei-mst-region]region-name huawei [Huawei-mst-region]revision-level 1 [Huawei-mst-region]instance 1 vlan 10 [Huawei-mst-region]instance 2 vlan 20 [Huawei-mst-region]active region-configuration Info: This operation may take a few seconds. Please wait for a moment...done.

三、需求5的結果

總結

也就LSW1配的多了點，其他問題不大。
因為本來寫的是簡寫，特地換成全寫，所以花了點時間，所以上一篇沒有寫命令，今天補上。

總結

以上是生活随笔為你收集整理的上个ensp实验只发了配置，这次是命令条目的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。