關閉

NVIDIA cuda7在centos6.5中的安裝

標簽： NVIDIAcuda7centos6-5安裝 2015-08-03 15:14 123人閱讀 評論(0)收藏 舉報 分類： CentOS（2）

版權聲明：本文為博主原創文章，未經博主允許不得轉載。

目錄(?)[+]

基本環境

• cuda_7.0.28_linux.run
• CentOS 6.5

安裝過程

• 禁用Nouveau，這個驅動和Nvidia的驅動有沖突，需要先禁用掉，不然會不讓安裝，具體可參考NVIDIA CUDA GETTING STARTED GUIDE FOR LINUX
  
• 創建文件，/etc/modprobe.d/blacklist-nouveau.conf，其內容如下：
  blacklist nouveau
  options nouveau modeset=0
• 重新生成kernel initramfs，即Regenerate the kernel initramfs，執行如下命令
  sudo dracut –force
  注意：force前面是2個-
• 設置系統啟動為Text Mode，即修改文件：/etc/inittab，將id:5改為id:3，讓系統不從界面化啟動，安裝完成后，再修改過來。注意，不要從界面啟動，然后通過按ctrl+alt+f3進入Text界面來進行安裝，這個好像會出問題，會不讓安裝。
• 重啟系統
• 直接運行cuda_7.0.28_linux.run，該文件需要有可執行權限
• 如果安裝時，提示X server is running，不讓進行安裝，則執行如下操作：
  
• 查詢下和X相關的服務，pstree -p | grep X
• 如果查詢知道有服務在運行，就kill掉，比如：
  |-Xvnc(2259)
  |-Xvnc(2299)
  這時候，就依次執行
  sudo kill -9 2259
  sudo kill -9 2299
  將相關服務給殺掉，這時候應該就可以安裝了
• 運行安裝文件后，根據提示進行默認安裝即可。安裝完成后需要配置PATH和LD_LIBRARY_PATH。
• 將id:3修改回為id:5，重啟系統。
• 如果重啟后停留在進度條界面，正常進不了界面化的登錄界面，則按ctrl+alt+f3進入Text界面，登錄進入系統。然后查看/etc/X11/xorg.conf文件是否存在。一般是因為這個文件不存在導致的。這時候執行如下命令：
  nvidia-xconfig
  該命令會生成相應的xorg.conf文件

其他命令

• 在系統啟動時，即進度條狀態時，按下Esc鍵，會轉換到類似CMD命令似的界面，會顯示相關的啟動日志，可以查看相關東西。
• 也可以通過查看/var/log/文件夾下的Xorg.*類文件來查看啟動日志，比如
  ls /var/log/Xorg.*
  會顯示相關的文件：
  /var/log/Xorg.0.log
  /var/log/Xorg.1.log
  /var/log/Xorg.2.log
  一般Xorg.0.log是最新的日志文件，可以通過時間知道。

重要參考

endly nvidia-xconfig
NVIDIA CUDA GETTING STARTED GUIDE FOR LINUX

之前都是在Centos6下進行CUDA開發，安裝和配置CUDA環境請參考另外一篇博客（Linux（redhat）CUDA安裝）。因為Centos7有較大變動，所以安裝CUDA過程中遇到了一些麻煩，原因初步歸結于OpenGL的安裝。下面詳細介紹安裝配置過程

關閉防火墻和selinux和補充包和建立本地yum源

[root@localhost ~]# systemctl stop firewalld.service?
[root@localhost ~]# systemctl disable firewalld.service?
rm '/etc/systemd/system/dbus-org.fedoraproject.FirewallD1.service'
rm '/etc/systemd/system/basic.target.wants/firewalld.service'
[root@localhost ~]# vi /etc/selinux/config?
[root@localhost ~]# cat /etc/selinux/config?


# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
# ? ? enforcing - SELinux security policy is enforced.
# ? ? permissive - SELinux prints warnings instead of enforcing.
# ? ? disabled - No SELinux policy is loaded.
SELINUX=disabled
# SELINUXTYPE= can take one of three two values:
# ? ? targeted - Targeted processes are protected,
# ? ? minimum - Modification of targeted policy. Only selected processes are protected.?
# ? ? mls - Multi Level Security protection.
SELINUXTYPE=targeted?
重新啟動繼續配置
=============================================================================================
[root@localhost ~]# cd /etc/yum.repos.d/
[root@localhost yum.repos.d]# mkdir -p ./bak
[root@localhost yum.repos.d]# mv *.repo ./bak/
[root@localhost yum.repos.d]# vi local.repo
[root@localhost yum.repos.d]# cat local.repo
[local_server]
name=This is a local repo
baseurl=file:///mnt/iso
enabled=1
gpgcheck=0
[root@localhost yum.repos.d]# yum clean all
[root@localhost yum.repos.d]# mkdir -p /mnt/iso
[root@localhost yum.repos.d]# mount -o loop /cudainstall/CentOS\ 7\ x86_64.iso /mnt/iso/
[root@localhost yum.repos.d]# vi /etc/rc.local?
[root@localhost yum.repos.d]# chmod +x /etc/rc.d/rc.local
[root@localhost yum.repos.d]# cat /etc/rc.lcoa
cat: /etc/rc.lcoa: Aucun fichier ou dossier de ce type
[root@localhost yum.repos.d]# cat /etc/rc.local?
#!/bin/bash
# THIS FILE IS ADDED FOR COMPATIBILITY PURPOSES
#
# It is highly advisable to create own systemd services or udev rules
# to run scripts during boot instead of using this file.
#
# In contrast to previous versions due to parallel execution during boot
# this script will NOT be run after all other services.
#
# Please note that you must run 'chmod +x /etc/rc.d/rc.local' to ensure
# that this script will be executed during boot.
mount -o loop /cudainstall/CentOS\ 7\ x86_64.iso /mnt/iso/
touch /var/lock/subsys/local


[root@localhost yum.repos.d]# hostnamectl set-hostname cuda02
[root@cuda02 ~]# yum install kernel-devel gcc gcc-c++ yum install libX*




檢查nouveau
[root@cuda01 ~]# lsmod |grep nouveau


如果有輸出 使用modprobe -r nouveau
[root@cuda01 ~]#init 3
==================================================================================================
安裝cuda時一定不要安裝OpenGL；切記，否則有可能安裝完之后，圖形化桌面啟動不了，過程中會出現如下錯誤信息
[root@cuda02 cudainstall]# chmod +x cuda_7.0.28_linux.run
[root@cuda02 cudainstall]# ./cuda_7.0.28_linux.run
Do you accept the previously read EULA? (accept/decline/quit): accept ? ? ?
Install NVIDIA Accelerated Graphics Driver for Linux-x86_64 346.46? ((y)es/(n)o/(q)uit): y
Do you want to install the OpenGL libraries? ((y)es/(n)o/(q)uit) [ default is yes ]: n
Install the CUDA 7.0 Toolkit? ((y)es/(n)o/(q)uit): y
Enter Toolkit Location [ default is /usr/local/cuda-7.0 ]:?
Do you want to install a symbolic link at /usr/local/cuda? ((y)es/(n)o/(q)uit): y
Install the CUDA 7.0 Samples? ((y)es/(n)o/(q)uit): y
Enter CUDA Samples Location [ default is /root ]:?
Installing the NVIDIA display driver...
Installing the CUDA Toolkit in /usr/local/cuda-7.0 ...
Missing recommended library: libGLU.so


Installing the CUDA Samples in /root ...
Copying samples to /root/NVIDIA_CUDA-7.0_Samples now...
Finished copying samples.


===========
= Summary =
===========


Driver: ? Installed
Toolkit: ?Installed in /usr/local/cuda-7.0
Samples: ?Installed in /root, but missing recommended libraries


Please make sure that
?- ? PATH includes /usr/local/cuda-7.0/bin
?- ? LD_LIBRARY_PATH includes /usr/local/cuda-7.0/lib64, or, add /usr/local/cuda-7.0/lib64 to /etc/ld.so.conf and run ldconfig as root


To uninstall the CUDA Toolkit, run the uninstall script in /usr/local/cuda-7.0/bin
To uninstall the NVIDIA Driver, run nvidia-uninstall


Please see CUDA_Getting_Started_Guide_For_Linux.pdf in /usr/local/cuda-7.0/doc/pdf for detailed information on setting up CUDA.


Logfile is /tmp/cuda_install_2994.log



安裝cuda驅動
[root@cuda02 cudainstall]# chmod +x cuda_7.0.28_linux.run
[root@cuda02 cudainstall]# ./cuda_7.0.28_linux.run
Do you accept the previously read EULA? (accept/decline/quit): accept ? ? ?
Install NVIDIA Accelerated Graphics Driver for Linux-x86_64 346.46? ((y)es/(n)o/(q)uit): y
Do you want to install the OpenGL libraries? ((y)es/(n)o/(q)uit) [ default is yes ]: n
Install the CUDA 7.0 Toolkit? ((y)es/(n)o/(q)uit): y
Enter Toolkit Location [ default is /usr/local/cuda-7.0 ]:?
Do you want to install a symbolic link at /usr/local/cuda? ((y)es/(n)o/(q)uit): y
Install the CUDA 7.0 Samples? ((y)es/(n)o/(q)uit): y
Enter CUDA Samples Location [ default is /root ]:?
Installing the NVIDIA display driver...
Installing the CUDA Toolkit in /usr/local/cuda-7.0 ...
Missing recommended library: libGLU.so


Installing the CUDA Samples in /root ...
Copying samples to /root/NVIDIA_CUDA-7.0_Samples now...
Finished copying samples.


===========
= Summary =
===========


Driver: ? Installed
Toolkit: ?Installed in /usr/local/cuda-7.0
Samples: ?Installed in /root, but missing recommended libraries


Please make sure that
?- ? PATH includes /usr/local/cuda-7.0/bin
?- ? LD_LIBRARY_PATH includes /usr/local/cuda-7.0/lib64, or, add /usr/local/cuda-7.0/lib64 to /etc/ld.so.conf and run ldconfig as root


To uninstall the CUDA Toolkit, run the uninstall script in /usr/local/cuda-7.0/bin
To uninstall the NVIDIA Driver, run nvidia-uninstall


Please see CUDA_Getting_Started_Guide_For_Linux.pdf in /usr/local/cuda-7.0/doc/pdf for detailed information on setting up CUDA.


Logfile is /tmp/cuda_install_2994.log


廣播cuda的路徑
[root@cuda02 cudainstall]# vi /etc/profile.d/cuda.sh
[root@cuda02 cudainstall]# cat /etc/profile.d/cuda.sh?
export PATH=/usr/local/cuda-7.0/bin:$PATH
export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/usr/local/cuda-7.0/lib64
[root@cuda02 cudainstall]# chmod 755 /etc/profile.d/cuda.sh?
[root@cuda02 cudainstall]# source /etc/profile.d/cuda.sh
[root@cuda02 cudainstall]#?
=================================================================================================================
恢復圖形界面顯示
[root@cuda02 cudainstall]# init 5
=================================================================================================================
安裝vnc
[root@cuda02 cudainstall]# yum -y install tigervnc-server

總結

以上是生活随笔為你收集整理的NVIDIA cuda7在centos6.5中的安装的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。