學習目標

?

·?掌握接口速率的配置方法

·?掌握使用手動模式配置鏈路聚合的方法

·?掌握使用靜態LACP模式配置鏈路聚合的方法

·?掌握在靜態LACP模式下配置接口優先級的方法

?

拓?fù)鋱D

圖4.1 以太網鏈路聚合拓?fù)鋱D

?

場景

?

您是公司的網絡管理員。現在公司購買了兩臺華為的S5700系列的交換機，為了提高交換機之間鏈路帶寬以及可靠性，您需要在交換機上配置鏈路聚合功能。

?

操作步驟

?

步驟一?以太網交換機基礎配置

華為交換機接口默認開啟了自協商功能。

首先修改交換機的設備名稱，然后查看SW1上G0/0/9和G0/0/10接口的詳細信息。

?

<Huawei>system-view[Huawei]sysname SW1[SW1][SW1]display interface GigabitEthernet 0/0/9GigabitEthernet0/0/9 current state : UPLine protocol current state : UPDescription:Switch Port, Link-type : trunk(negotiated),PVID : 1, TPID : 8100(Hex), The Maximum Frame Length is 9216IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is d0d0-4ba6-aab0Current system time: 2019-11-23 14:18:37Port Mode: COMMON COPPERSpeed : 1000, Loopback: NONEDuplex: FULL, Negotiation: ENABLEMdi : AUTO, Flow-control: DISABLELast 300 seconds input rate 256 bits/sec, 0 packets/secLast 300 seconds output rate 912 bits/sec, 0 packets/secInput peak rate 13976 bits/sec, Record time: 2019-11-22 14:59:12Output peak rate 13976 bits/sec, Record time: 2019-11-22 14:59:12……output omit……

?

???????

[SW1]display interface GigabitEthernet 0/0/10GigabitEthernet0/0/10 current state : UPLine protocol current state : UPDescription:Switch Port, Link-type : trunk(negotiated),PVID : 1, TPID : 8100(Hex), The Maximum Frame Length is 9216IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is d0d0-4ba6-aab0Current system time: 2019-11-23 14:22:22Port Mode: COMMON COPPERSpeed : 1000, Loopback: NONEDuplex: FULL, Negotiation: ENABLEMdi : AUTO, Flow-control: DISABLELast 300 seconds input rate 72 bits/sec, 0 packets/secLast 300 seconds output rate 1024 bits/sec, 0 packets/secInput peak rate 14032 bits/sec, Record time: 2019-11-22 14:59:12Output peak rate 14032 bits/sec, Record time: 2019-11-22 14:59:12……output omit……

?

步驟二?配置手動模式的鏈路聚合

• ?

在SW1和SW2上創建Eth-Trunk 1，然后將G0/0/9和G0/0/10接口加入Eth-Trunk 1（注意：將接口加入Eth-Trunk前需確認成員接口下沒有任何配置）。[SW1]interface Eth-Trunk 1[SW1-Eth-Trunk1]quit[SW1]interface GigabitEthernet 0/0/9[SW1-GigabitEthernet0/0/9]eth-trunk 1[SW1-GigabitEthernet0/0/9]quit[SW1]interface GigabitEthernet 0/0/10[SW1-GigabitEthernet0/0/10]eth-trunk 1[SW2]interface Eth-Trunk 1[SW2-Eth-Trunk1]quit[SW2]interface GigabitEthernet 0/0/9[SW2-GigabitEthernet0/0/9]eth-trunk 1[SW2-GigabitEthernet0/0/9]quit[SW2]interface GigabitEthernet 0/0/10[SW2-GigabitEthernet0/0/10]eth-trunk 1驗證Eth-Trunk的配置結果。[SW1]display eth-trunk 1Eth-Trunk1's state information is:WorkingMode: NORMAL Hash arithmetic: According to SIP-XOR-DIP Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 8 Operate status: up Number Of Up Port In Trunk: 2 ----------------------------------------------------------------------------PortName Status WeightGigabitEthernet0/0/9 Up 1 GigabitEthernet0/0/10 Up 1 [SW2]display eth-trunk 1Eth-Trunk1's state information is:WorkingMode: NORMAL Hash arithmetic: According to SIP-XOR-DIP Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 8 Operate status: up Number Of Up Port In Trunk: 2 ----------------------------------------------------------------------------PortName Status WeightGigabitEthernet0/0/9 Up 1 GigabitEthernet0/0/10 Up 1

回顯信息中灰色陰影標注的部分表明Eth-Trunk工作正常，成員接口都已正確加入。

在SW1上查看接口聚合后帶寬

• ?

[SW1]display interface Eth-Trunk 1Eth-Trunk1 current state : UPLine protocol current state : UPDescription:Switch Port, PVID : 1, Hash arithmetic : According to SIP-XOR-DIP,Maximal BW: 2G, Current BW: 2G, The Maximum Frame Length is 9216IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 4c1f-cc16-05acCurrent system time: 2020-03-15 15:33:56-08:00 Input bandwidth utilization : 0% Output bandwidth utilization : 0%-------------------------------------------------------------------PortName Status Weight-------------------------------------------------------------------GigabitEthernet0/0/9 UP 1GigabitEthernet0/0/10 UP 1-------------------------------------------------------------------The Number of Ports in Trunk : 2The Number of UP Ports in Trunk : 2

?

在SW2上查看接口聚合后帶寬

• ?

[SW2]display interface Eth-Trunk 1Eth-Trunk1 current state : UPLine protocol current state : UPDescription:Switch Port, PVID : 1, Hash arithmetic : According to SIP-XOR-DIP,Maximal BW: 2G, Current BW: 2G, The Maximum Frame Length is 9216IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 4c1f-cc78-50fbCurrent system time: 2020-03-15 15:35:33-08:00 Input bandwidth utilization : 0% Output bandwidth utilization : 0%-------------------------------------------------------------------PortName Status Weight-------------------------------------------------------------------GigabitEthernet0/0/9 UP 1GigabitEthernet0/0/10 UP 1-------------------------------------------------------------------The Number of Ports in Trunk : 2The Number of UP Ports in Trunk : 2

?

步驟三?配置靜態LACP模式的鏈路聚合

刪除SW1和SW2上的G0/0/9和G0/0/10接口下的配置。

• ?

[SW1]interface GigabitEthernet 0/0/9[SW1-GigabitEthernet0/0/9]undo eth-trunk[SW1-GigabitEthernet0/0/9]quit[SW1]interface GigabitEthernet 0/0/10[SW1-GigabitEthernet0/0/10]undo eth-trunk[SW2]interface GigabitEthernet 0/0/9[SW2-GigabitEthernet0/0/9]undo eth-trunk[SW2-GigabitEthernet0/0/9]quit[SW2]interface GigabitEthernet 0/0/10[SW2-GigabitEthernet0/0/10]undo eth-trunk

?

創建Eth-Trunk 1并配置該Eth-Trunk為靜態LACP模式。然后將G0/0/9和G0/0/10接口加入Eth-Trunk 1。

• ?

[SW1]interface Eth-Trunk 1[SW1-Eth-Trunk1]mode lacp[SW1-Eth-Trunk1]quit [SW1]interface GigabitEthernet 0/0/9[SW1-GigabitEthernet0/0/9]eth-trunk 1[SW1-GigabitEthernet0/0/9]quit[SW1]interface GigabitEthernet 0/0/10[SW1-GigabitEthernet0/0/10]eth-trunk 1[SW2]interface Eth-Trunk 1[SW2-Eth-Trunk1]mode lacp[SW2-Eth-Trunk1]quit[SW2]interface GigabitEthernet 0/0/9[SW2-GigabitEthernet0/0/9]eth-trunk 1[SW2-GigabitEthernet0/0/9]quit[SW2]interface GigabitEthernet 0/0/10[SW2-GigabitEthernet0/0/10]eth-trunk 1

?

查看交換機上Eth-Trunk的信息，查看鏈路是否協商成功。

• ?

[SW1]disp eth-trunk 1Eth-Trunk1's state information is:Local:LAG ID: 1 WorkingMode: STATIC Preempt Delay: Disabled Hash arithmetic: According to SIP-XOR-DIP System Priority: 32768 System ID: 4c1f-cc16-05ac Least Active-linknumber: 1 Max Active-linknumber: 8 Operate status: up Number Of Up Port In Trunk: 2 --------------------------------------------------------------------------------ActorPortName Status PortType PortPri PortNo PortKey PortState WeightGigabitEthernet0/0/9 Selected 1GE 32768 10 305 10111100 1 GigabitEthernet0/0/10 Selected 1GE 32768 11 305 10111100 1 Partner:--------------------------------------------------------------------------------ActorPortName SysPri SystemID PortPri PortNo PortKey PortStateGigabitEthernet0/0/9 32768 4c1f-cc78-50fb 32768 10 305 10111100GigabitEthernet0/0/10 32768 4c1f-cc78-50fb 32768 11 305 10111100[SW2]display eth-trunk 1Eth-Trunk1's state information is:Local:LAG ID: 1 WorkingMode: STATIC Preempt Delay: Disabled Hash arithmetic: According to SIP-XOR-DIP System Priority: 32768 System ID: 4c1f-cc78-50fb Least Active-linknumber: 1 Max Active-linknumber: 8 Operate status: up Number Of Up Port In Trunk: 2 --------------------------------------------------------------------------------ActorPortName Status PortType PortPri PortNo PortKey PortState WeightGigabitEthernet0/0/9 Selected 1GE 32768 10 305 10111100 1 GigabitEthernet0/0/10 Selected 1GE 32768 11 305 10111100 1 Partner:--------------------------------------------------------------------------------ActorPortName SysPri SystemID PortPri PortNo PortKey PortStateGigabitEthernet0/0/9 32768 4c1f-cc16-05ac 32768 10 305 10111100GigabitEthernet0/0/10 32768 4c1f-cc16-05ac 32768 11 305 10111100

?

在SW1上配置LACP的系統優先級為100，使其成為LACP主動端。

[SW1]lacp ?priority 100

?

配置接口的優先級確定活動鏈路。

• ?

[SW1]interface GigabitEthernet 0/0/9[SW1-GigabitEthernet0/0/9]lacp priority 100[SW1-GigabitEthernet0/0/9]quit[SW1]interface GigabitEthernet 0/0/10[SW1-GigabitEthernet0/0/10]lacp priority 100

?

驗證Eth-Trunk的配置結果。

• ?
• ?

[SW1]display eth-trunk 1Eth-Trunk1's state information is:Local:LAG ID: 1 WorkingMode: STATIC Preempt Delay: Disabled Hash arithmetic: According to SIP-XOR-DIP System Priority: 100 System ID: 4c1f-cc16-05ac Least Active-linknumber: 1 Max Active-linknumber: 8 Operate status: up Number Of Up Port In Trunk: 2 --------------------------------------------------------------------------------ActorPortName Status PortType PortPri PortNo PortKey PortState WeightGigabitEthernet0/0/9 Selected 1GE 100 10 305 10111100 1 GigabitEthernet0/0/10 Selected 1GE 100 11 305 10111100 1 Partner:--------------------------------------------------------------------------------ActorPortName SysPri SystemID PortPri PortNo PortKey PortStateGigabitEthernet0/0/9 32768 4c1f-cc78-50fb 32768 10 305 10111100GigabitEthernet0/0/10 32768 4c1f-cc78-50fb 32768 11 305 10111100[SW2]display eth-trunk 1Eth-Trunk1's state information is:Local:LAG ID: 1 WorkingMode: STATIC Preempt Delay: Disabled Hash arithmetic: According to SIP-XOR-DIP System Priority: 32768 System ID: 4c1f-cc78-50fb Least Active-linknumber: 1 Max Active-linknumber: 8 Operate status: up Number Of Up Port In Trunk: 2 --------------------------------------------------------------------------------ActorPortName Status PortType PortPri PortNo PortKey PortState WeightGigabitEthernet0/0/9 Selected 1GE 32768 10 305 10111100 1 GigabitEthernet0/0/10 Selected 1GE 32768 11 305 10111100 1 Partner:--------------------------------------------------------------------------------ActorPortName SysPri SystemID PortPri PortNo PortKey PortStateGigabitEthernet0/0/9 100 4c1f-cc16-05ac 100 10 305 10111100GigabitEthernet0/0/10 100 4c1f-cc16-05ac 100 11 305 10111100

?

?

配置文件

?

• [SW1]display current-configuration [SW2]display current-configuration

end

總結

以上是生活随笔為你收集整理的给华为S5700交换机配下链路聚合的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。