轉載自?http://www.javacodegeeks.com/2011/04/erlang-vs-java-memory-architecture.html

I read a really, really interesting article on memory management strategies for the?Erlang?VM. It was written as a?thesis?by?Jesper Wilhelmsson?I thought it might be nice to discuss the differences between?Erlang's memory setup and Oracle's Java VM.

As a real short introduction for those who have never heard of?Erlang; it is a functional language that uses asynchronous message passing as its basis for concurrency. The message passing uses copy semantics, making distribution over more than one?Erlang?VM, running on more than one machine essentially transparent to the programmer.

Erlang?and Java are similar in the sense that both use a virtual machine to abstract the hardware into a portable layer. Both languages employ machine independent byte code. Both run-time systems rely on garbage collection to free the programmer of doing memory management.

Threading overhead in?Erlang?is very low. I believe that the memory requirements for a thread inErlang?is about 512 bytes. In Java threads typically need about 512 kilobytes, about 1000 times more. For a programmer, the upshot is that creating threads to do some work asynchronously is not something you have to sit down and think about. Typical?Erlang?systems have thousands or tens of thousands of threads. There is no futzing with threadpools and executors like we do in Java.

From what little I have dabbled with it, I found?Erlang?to be a pleasant compromise between a functional language, and a language that allows you to write real-world applications. (I know I'll get flak for this) Robust distributed error handling is a pleasant surprise and writing a network server of any kind is actually easy. The state-machine approach to web servers makes rolling back on errors completely natural.

But this post is not about the programming model of?Erlang. It is about the way the?Erlang?VM deals with memory.

The current Java virtual machine uses what an?Erlang?programmer would call a shared heap topology. There is one big heap that is used by all threads. Most memory is allocated on that heap. In addition to the heap, the JVM uses some specialised data areas like the code cache and the permanent generation. These too are shared between all threads.

By contrast,?Erlang?uses a private heap topology. Each thread has its own tiny heap that contains all data the thread uses and the thread's stack as well. All data for a thread is on that local heap. It is reserved when the thread is created. When the thread dies, the entire heap is simply returned to the pool of free memory.

Aside from the private heaps, all threads share access to a so-called binary heap and a message heap. These are specialised heaps. The binary heap is for allocating large chunks of arbitrary data that are likely to be shared between threads. This is where for example file input or network buffers live.

The message heap is a heap for data that is used in messages. Messages too are shared between processes. Messages are passed between threads by copying a pointer over from the sending thread to the receiving thread. The data for the message is stored on the message heap.

I was impressed by the?Erlang?memory model. It just strikes me as a lot more scalable than Java's single heap model. The language semantics and the memory model match beautifully.

For instance; the simple fact that heaps are private to a thread relieves the threads of all forms of lock checking on their own data. Add to that the fact that there are no destructive writes and suddenly there is no need for lock checking for shared data either.

The latest version of the?Erlang?VM take this yet another step further by having more than one scheduler. One scheduler per physical processor to be precise. This eliminates another entire class of locks to check. Only when a scheduler is bored it needs to go out, gather a lock and get some processes off of another scheduler.

In Java, we have a lot to learn still. That said, we have a few nice things in Java that I miss working with large?Erlang?systems.

The?Erlang?VM will reallocate and grow heaps when thread accumulate a lot of data. However, the reallocation algorithm causes heap sizes to grow rapidly. Under high load, we have seen?Erlang?VM's eat up 16GB of RAM in a matter of minutes. Each release has to be carefully load tested to see if its memory requirements are still sane.

There are no mechanisms in the?Erlang?VM to curb the growth of the memory. The VM will happily allocate so much memory that the system shoots into swap, or that the virtual memory is exhausted. These may cause the machine to become unresponsive even to KVM console access. In the past we have had to power cycle machines to get access to them again.

The queue-based programming model that makes?Erlang?so much fun to write code for, is also it Achilles heel in production. Every queue in?Erlang?is unbounded. The VM will not throw exceptions or limit the number of messages in a queue. Sometimes a process stops processing due to a bug, or a process fails to keep up with the flow of messages being sent to it. In that case,?Erlang?will simply allow the queue for that process to grow until either the VM is killed or the machine locks up, whichever comes first.

This means that when you run large?Erlang?VM's in a production environment you need to have OS-level checks that will kill the process if memory use skyrockets. Remote hands for the machine, or remote access cards is a must-have for machines that run large?Erlang?VM's.

In summary, for every day performance I believe the private heap memory model to be a very powerful tool in?Erlang's box. It cuts whole classes of locking mechanisms out of the run-time system and that means it will scale better than Java will for the same purpose. Java's hard limits on memory will save your bacon when your system is being flooded or DDoSed.

Last thoughts,

There is a command line switch for?Erlang's VM to switch it from using the private heap topology to using the share heap topology.

I like?Erlang?and Java. They are hard to compare because the have so little in common for a developer. In general, I would use Java for most systems, though. Tool support is better and the number of libraries available is staggering. I would opt for?Erlang?in the case where I have a stream oriented messaging system. That's when the?Erlang?programming model really shines.


References :

• Erlang memory architecture vs Java memory architecture?from our?JCG?partner?Kees Jan Koster?at?Java-Monitor

Happy Coding! Do not forget to share!

Byron

轉載于:https://www.cnblogs.com/dikanggu/archive/2011/04/13/2015192.html

總結

以上是生活随笔為你收集整理的Erlang vs Java memory architecture (zz)的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。