GNS中支持的模块
?Dynamips?支持的模塊
C7200?開始
Slot 0:
C7200-IO-FE?<------>?支持1?個Fastethernet?接口
C7200-IO-2FE?<------>?支持2?個Fastethernet?接口(DynamipsGUI 2.3?里面沒有這個選項,想用只有自己添
加了)
C7200-IO-GE-E?<------>?插這個卡以后會同時出現2?個端口,Ethernet0/0?和GigabitEthernet0/0 (反正我沒有
用到過這個卡)
注意:這三個卡只允許插在Slot0?口,如果插入后面的slot?口是無效的.
Slot 1-5:
PA-2FE-TX?<------>?支持2?個Fastethernet?接口
PA-FE-TX?<------>?支持1?個Fastethernet?接口
PA-4E?<------>?支持4?個Ethernet?接口
PA-4T+?<------>?支持4?個serial?接口
PA-8E <------>?支持8?個Ethernet?接口
PA-8T?<------>?支持8?個serial?接口
PA-A1?<------>?支持1?個ATM port adapter?接口
PA-GE?<------>?支持1?個GigabitEthernet?接口
PA-POS-OC3<------>?支持1?個Packet Over SONET/SDH?接口(用于更高速度的接口)
C3600(3620/3640/3660)
NM-16ESW?<------>?支持16?個Fastethernet?接口(交換模塊,在使用此模塊做交換實驗時候,請使用no iprouting?關閉端口路由)
NM-1E?<------>?支持1?個Ethernet?接口
NM-1FE-TX<------>?支持1?個Fastethernet?接口
NM-4E?<------>?支持4?個Ethernet?接口
NM-4T?<------>?支持4?個serial?接口
Leopard-2FE<------>支持2?個Fastethernet?接口(3660?專用,并且只能在slot 0?下使用)
c3725/c3745/c2691
GT96100-FE?<------>支持2?個Fastethernet?接口(只限制在slot 0)
NM-16ESW?<------>支持16?個Fastethernet?接口(不做重復說明)
NM-1FE-TX?<------>支持1?個Fastethernet?接口
NM-4T?<------>支持4?個serial?接口
c2600(2610/2611/2620/2621/2610XM/2620XM/2650XM)
NM-16ESW?<------>?支持16?個Fastethernet?接口
NM-1E?<------>?支持1?個Ethernet?接口
NM-1FE-TX<------>?支持1?個Fastethernet?接口
NM-4E?<------>?支持4?個Ethernet?接口
CISCO2600-MB-2E<------>支持2?個Ethernet?接口
CISCO2600-MB-2FE<------>支持2?個Fastethernet?接口
轉載于:https://blog.51cto.com/forcecity/511938
總結
- 上一篇: 机器学习中的算法(1)-决策树模型组合之
- 下一篇: 使用PostSharp开始AOP