This new suite of tests requires human intervention and some external hardware including a?Loopback Plug, a?USB reference microphone?and?external speakers. For devices without 3.5 mm (?”) headset port, the user will be able to skip the test and mark it as successful. See the sections below for details.

Loopback plug latency test

Round trip latency?in audio is defined as the time it takes an audio signal to be recorded, processed and output back.

To measure round-trip latency using CTS Verifier, connect a loopback plug to the 3.5 mm (?”) headset connector. (If you don’t have a loopback plug, you can easily make one following the?Audio Loopback Dongle?instructions.

Start CTS Verifier Loopback Test

Summary of instructions is displayed

Report if the device has a headset port:

YES?if the device under test has a physical headset port

NO?if there is no headset port

If the answer was?NO?in the previous step, press?Pass?(green check) on the bottom of the test and finish

If the answer was?YES?in the previous step, continue to connect loopback plug.

Connect a loopback plug to the headset port

Press the?Loopback Plug Ready?button

Move the slider until the signal level is greater than 60%

Press?TEST

?

Wait several seconds while the latency test is performed

When the test is finished, results are shown

The minimum confidence level for a test to succeed is 0.6

Lower latency numbers are preferred, but no number is enforced

Press the?Pass?(green, only available if successful) or?Failed?(red) button to record the results.

Audio frequency line test

Using a loopback plug, this test will characterize the left/right line audio output and use the mic feedback from the plug to capture audio and compute a frequency response for each channel.

A simple criterion for minimum energy expected in each band (out of four) is applied per channel.

Start CTS Audio Frequency Line Test

Summary of instructions is displayed

Report if the device has a headset port:

YES?if the device under test has a physical headset port

NO?if there is no headset port

If the answer was?NO?in the previous step, press?Pass?(green check) on the bottom of the test and finish

If the answer was?YES?in the previous step, continue to connect loopback plug

Connect a Loopback Plug to the headset connector (see?Loopback plug latency test)

Press the?Loopback Plug Ready?button

Press?TEST

Wait several seconds while the frequency tests are performed

When the test is finished, results are shown

Press the?Pass?(only available if successful) or?Failed?button to record the results

Audio frequency speaker test

This test uses the signal captured by an external USB reference microphone to assess the frequency response of left (and right, if it exists) loudspeakers.

A reference microphone is defined as that one that delivers flat, uncolored response. They are often used for analysis and measurement equipment.

There are some inexpensive USB Reference microphones (e.g.,?miniDSP USB Measurement calibrated microphone,?Dayton Audio UMM-6 USB Measurement Microphone), mostly used for the home theater enthusiasts to calibrate their setups.

Minimum recommended reference microphone characteristics:

Flat Frequency response on range 100 Hz – 20 kHz: +/- 2 dB

S/N ration 70 dB (A-weighted)

THD Ratio @ 1000 Hz less than 1 % at 127 dB SPL

Start CTS Audio Frequency Speaker Test

Summary of instructions is displayed

Connect a USB reference microphone (see?Audio frequency speaker test)

Press?USB REFERENCE MICROPHONE READY

Set up DUT (Device Under Test) in a quiet room and USB microphone 20cms perpendicular to center of screen

Press?TEST

Wait several seconds while the frequency tests are performed

When the test is finished, results are shown

Press the?Pass?(only available if successful) or?Failed?button to record the results

Audio frequency microphone test

This test is more involved than the previous ones. It requires the use of both: External speakers for a white noise sound source, and a USB reference microphone to use as a reference for the sound. Although this process is more involved, it can be performed with affordable, easy to get, hardware

External speakers positioned 40cm from the device are used to deliver a white noise sound source. These speakers don’t need to have a “Flat” frequency response, but need good coverage from low frequencies (100 hz) to high frequencies (20khz) is expected which is usually met by portable or medium size self powered speakers (e.g. Sony SRS-X5 portable speakers)

The key element here is that a step for calibration (using the USB reference microphone) is performed, to estimate the actual response of the speakers, thus have a solid reference to compare the built in microphone against.

Start CTS Audio Frequency Microphone Test

Summary of instructions is displayed

Set up DUT in a quiet room

Position the speakers 40cm perpendicular to the center of the screen of the DUT (see?Audio frequency microphone test?)

Report if the device has a headset port:

YES?if the device under test has a physical headset port

NO?if there is no headset port

If the answer was?NO?in the previous step, press?Pass?(green check) on the bottom of the test and finish

If the answer was?YES?in the previous step, continue to connect external speakers.

Connect external speakers using the headphone/line out connector (remember to unplug any USB microphone)

Press?EXTERNAL SPEAKERS READY

Press?TEST 1

Wait several seconds for test 1 to complete.

When test 1 is completed, results for the built in microphone are shown.

Connect a USB Reference microphone (see?Audio frequency speaker test?)

Press?USB REFERENCE MICROPHONE READY

Position USB microphone right next to built-in microphone in DUT, pointing towards external speakers

Press?TEST 2

Wait several seconds while the test 2 runs

When test 2 is completed, results for the USB reference microphone are shown.

Press the?Pass?(only available if successful) or?Failed?button to record the results.

總結(jié)

以上是生活随笔為你收集整理的android 副mic测试,【收藏】Android Audio Framework CTS Verifier 测试方法的全部內(nèi)容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網(wǎng)站內(nèi)容還不錯，歡迎將生活随笔推薦給好友。