最近在Zynq板上啟動linaro桌面系統時，發現一個奇怪的問題，系統在啟動到最后，已經打印了如下信息：[drm] Initialized axi_hdmi_drm 1.0.0 20120930 on minor 0，按理說后面就該是登錄系統并顯示shell提示符了，但后面顯示：VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -30，即打不開SD卡的第二個分區，之前使用這張卡可正常啟動的，而且沒有做任何改動。于是我們重新制作桌面文件系統，結果問題依舊。很不解？！下面是啟動信息：

U-Boot 2013.01 (Jun 04 2013 - 09:22:41)

DRAM:? 512 MiB

WARNING: Caches not enabled

MMC:?? zynq_sdhci: 0

SF: Detected S25FL256S with page size 64 KiB, total 32 MiB

*** Warning - bad CRC, using default environment

In:??? serial

Out:?? serial

Err:?? serial

Net:?? Gem.e000b000

Hit any key to stop autoboot:? 0

Copying Linux from SD to RAM...

Device: zynq_sdhci

Manufacturer ID: 2

OEM: 544d

Name: SA08G

Tran Speed: 50000000

Rd Block Len: 512

SD version 2.0

High Capacity: Yes

Capacity: 7.3 GiB

Bus Width: 4-bit

reading uImage

3158312 bytes read in 485 ms (6.2 MiB/s)

reading devicetree.dtb

8172 bytes read in 13 ms (613.3 KiB/s)

## Booting kernel from Legacy Image at 03000000 ...

Image Name:?? Linux-3.6.0

Image Type:?? ARM Linux Kernel Image (uncompressed)

Data Size:??? 3158248 Bytes = 3 MiB

Load Address: 00008000

Entry Point:? 00008000

Verifying Checksum ... OK

## Flattened Device Tree blob at 02a00000

Booting using the fdt blob at 0x02a00000

Loading Kernel Image ... OK

OK

Loading Device Tree to 1fb4f000, end 1fb53feb ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Booting Linux on physical CPU 0

Linux version 3.6.0 (ubuntu@ubuntu) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-50) ) #1 SMP PREEMPT Sun Jun 2 13:37:48 CST 2013

CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d

CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

Machine: Xilinx Zynq Platform, model: Xilinx Zynq ZED

bootconsole [earlycon0] enabled

cma: CMA: reserved 40 MiB at 1d000000

Memory policy: ECC disabled, Data cache writealloc

PERCPU: Embedded 7 pages/cpu @c0fcf000 s7872 r8192 d12608 u32768

Built 1 zonelists in Zone order, mobility grouping on.? Total pages: 130048

Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait devtmpfs.mount=0

PID hash table entries: 2048 (order: 1, 8192 bytes)

Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

Memory: 512MB = 512MB total

Memory: 466556k/466556k available, 57732k reserved, 0K highmem

Virtual kernel memory layout:

vector? : 0xffff0000 - 0xffff1000?? (?? 4 kB)

fixmap? : 0xfff00000 - 0xfffe0000?? ( 896 kB)

vmalloc : 0xe0800000 - 0xff000000?? ( 488 MB)

lowmem? : 0xc0000000 - 0xe0000000?? ( 512 MB)

pkmap?? : 0xbfe00000 - 0xc0000000?? (?? 2 MB)

modules : 0xbf000000 - 0xbfe00000?? (? 14 MB)

.text : 0xc0008000 - 0xc0614ce4?? (6196 kB)

.init : 0xc0615000 - 0xc063dec0?? ( 164 kB)

.data : 0xc063e000 - 0xc06bcb80?? ( 507 kB)

.bss : 0xc06bcba4 - 0xc0bc4850?? (5152 kB)

Preemptible hierarchical RCU implementation.

RCU lockdep checking is enabled.

Dump stacks of tasks blocking RCU-preempt GP.

RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

NR_IRQS:512

MIO pin 11 not assigned(00001760)

xslcr mapped to e0802000

Zynq clock init

timer #0 at e0804000, irq=43

sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms

Console: colour dummy device 80x30

Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar

... MAX_LOCKDEP_SUBCLASSES:? 8

... MAX_LOCK_DEPTH:????????? 48

... MAX_LOCKDEP_KEYS:??????? 8191

... CLASSHASH_SIZE:????????? 4096

... MAX_LOCKDEP_ENTRIES:???? 16384

... MAX_LOCKDEP_CHAINS:????? 32768

... CHAINHASH_SIZE:????????? 16384

memory used by lock dependency info: 3695 kB

per task-struct memory footprint: 1152 bytes

Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

Setting up static identity map for 0x3a61a8 - 0x3a61dc

L310 cache controller enabled

l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72360000, Cache size: 524288 B

CPU1: Booted secondary processor

CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

Brought up 2 CPUs

SMP: Total of 2 processors activated (2664.03 BogoMIPS).

devtmpfs: initialized

NET: Registered protocol family 16

DMA: preallocated 256 KiB pool for atomic coherent allocations

xgpiops e000a000.gpio: gpio at 0xe000a000 mapped to 0xe080c000

hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.

hw-breakpoint: maximum watchpoint size is 4 bytes.

bio: create slab at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Linux video capture interface: v2.00

Advanced Linux Sound Architecture Driver Version 1.0.25.

Switching to clocksource xttcps_clocksource

NET: Registered protocol family 2

TCP established hash table entries: 16384 (order: 5, 131072 bytes)

TCP bind hash table entries: 16384 (order: 7, 589824 bytes)

TCP: Hash tables configured (established 16384 bind 16384)

TCP: reno registered

UDP hash table entries: 256 (order: 2, 20480 bytes)

UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)

NET: Registered protocol family 1

msgmni has been set to 991

io scheduler noop registered

io scheduler deadline registered

io scheduler cfq registered (default)

xuartps e0001000.uart: failed to get alias id, errno -19

e000console [ttyPS0] enabled, bootconsole disabled

console [ttyPS0] enabled, bootconsole disabled

xdevcfg f8007000.devcfg: ioremap f8007000 to e0814000 with size 1000

[drm] Initialized drm 1.1.0 20060810

platform 6c000000.axi_hdmi: Driver axi-hdmi requests probe deferral

brd: module loaded

loop: module loaded

xqspips e000d000.spi: master is unqueued, this is deprecated

xqspips e000d000.spi: at 0xE000D000 mapped to 0xE0816000, irq=51

libphy: XEMACPS mii bus: probed

xemacps e000b000.eth: pdev->id -1, baseaddr 0xe000b000, irq 54

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

ULPI transceiver vendor/product ID 0x0451/0x1507

Found TI TUSB1210 ULPI transceiver.

ULPI integrity check: passed.

xusbps-ehci xusbps-ehci.0: Xilinx PS USB EHCI Host Controller

xusbps-ehci xusbps-ehci.0: new USB bus registered, assigned bus number 1

xusbps-ehci xusbps-ehci.0: irq 53, io mem 0x00000000

xusbps-ehci xusbps-ehci.0: USB 2.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mousedev: PS/2 mouse device common for all mice

i2c /dev entries driver

usbcore: registered new interface driver uvcvideo

USB Video Class driver (1.1.1)

sdhci: Secure Digital Host Controller Interface driver

sdhci: Copyright(c) Pierre Ossman

sdhci-pltfm: SDHCI platform and OF driver helper

mmc0: Invalid maximum block size, assuming 512 bytes

mmc0: SDHCI controller on e0100000.sdhci [e0100000.sdhci] using ADMA

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

mmc0: new high speed SDHC card at address 1234

mmcblk0: mmc0:1234 SA08G 7.28 GiB (ro)

mmcblk0: p1 p2

adv7511 0-0039: Failed to add route AIFIN->TMDS

adv7511-hdmi-snd adv7511_hdmi_snd.4:? adv7511 75c00000.axi-spdif-tx mapping ok

INFO: task swapper/0:1 blocked for more than 20 seconds.

"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

swapper/0?????? D c03a4a84???? 0???? 1????? 0 0x00000000

[] (__schedule+0x540/0x658) from [] (schedule_timeout+0x18/0x164)

[] (schedule_timeout+0x18/0x164) from [] (wait_for_common+0xe0/0x174)

[] (wait_for_common+0xe0/0x174) from [] (_request_firmware_load+0xe0/0x180)

[] (_request_firmware_load+0xe0/0x180) from [] (request_firmware+0x74/0xb0)

[] (request_firmware+0x74/0xb0) from [] (_process_sigma_firmware+0x1c/0x1b4)

[] (_process_sigma_firmware+0x1c/0x1b4) from [] (process_sigma_firmware_regmap+0x18/0x24)

[] (process_sigma_firmware_regmap+0x18/0x24) from [] (adau17x1_load_firmware+0x58/0x7c)

[] (adau17x1_load_firmware+0x58/0x7c) from [] (adau1761_probe+0x2a8/0x30c)

[] (adau1761_probe+0x2a8/0x30c) from [] (soc_probe_codec+0x18c/0x29c)

[] (soc_probe_codec+0x18c/0x29c) from [] (snd_soc_register_card+0x724/0x10f4)

[] (snd_soc_register_card+0x724/0x10f4) from [] (platform_drv_probe+0x14/0x18)

[] (platform_drv_probe+0x14/0x18) from [] (driver_probe_device+0xb4/0x1ec)

[] (driver_probe_device+0xb4/0x1ec) from [] (__driver_attach+0x68/0x8c)

[] (__driver_attach+0x68/0x8c) from [] (bus_for_each_dev+0x48/0x74)

[] (bus_for_each_dev+0x48/0x74) from [] (bus_add_driver+0x98/0x220)

[] (bus_add_driver+0x98/0x220) from [] (driver_register+0x9c/0x13c)

[] (driver_register+0x9c/0x13c) from [] (do_one_initcall+0x90/0x164)

[] (do_one_initcall+0x90/0x164) from [] (kernel_init+0xf8/0x1b8)

[] (kernel_init+0xf8/0x1b8) from [] (kernel_thread_exit+0x0/0x8)

4 locks held by swapper/0/1:

#0:? (&__lockdep_no_validate__){......}, at: [] __driver_attach+0x40/0x8c

#1:? (&__lockdep_no_validate__){......}, at: [] __driver_attach+0x50/0x8c

#2:? (&card->mutex){+.+.+.}, at: [] snd_soc_register_card+0x274/0x10f4

#3:? (umhelper_sem){++++.+}, at: [] usermodehelper_read_trylock+0x4c/0xb8

INFO: task swapper/0:1 blocked for more than 20 seconds.

"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

swapper/0?????? D c03a4a84???? 0???? 1????? 0 0x00000000

[] (__schedule+0x540/0x658) from [] (schedule_timeout+0x18/0x164)

[] (schedule_timeout+0x18/0x164) from [] (wait_for_common+0xe0/0x174)

[] (wait_for_common+0xe0/0x174) from [] (_request_firmware_load+0xe0/0x180)

[] (_request_firmware_load+0xe0/0x180) from [] (request_firmware+0x74/0xb0)

[] (request_firmware+0x74/0xb0) from [] (_process_sigma_firmware+0x1c/0x1b4)

[] (_process_sigma_firmware+0x1c/0x1b4) from [] (process_sigma_firmware_regmap+0x18/0x24)

[] (process_sigma_firmware_regmap+0x18/0x24) from [] (adau17x1_load_firmware+0x58/0x7c)

[] (adau17x1_load_firmware+0x58/0x7c) from [] (adau1761_probe+0x2a8/0x30c)

[] (adau1761_probe+0x2a8/0x30c) from [] (soc_probe_codec+0x18c/0x29c)

[] (soc_probe_codec+0x18c/0x29c) from [] (snd_soc_register_card+0x724/0x10f4)

[] (snd_soc_register_card+0x724/0x10f4) from [] (platform_drv_probe+0x14/0x18)

[] (platform_drv_probe+0x14/0x18) from [] (driver_probe_device+0xb4/0x1ec)

[] (driver_probe_device+0xb4/0x1ec) from [] (__driver_attach+0x68/0x8c)

[] (__driver_attach+0x68/0x8c) from [] (bus_for_each_dev+0x48/0x74)

[] (bus_for_each_dev+0x48/0x74) from [] (bus_add_driver+0x98/0x220)

[] (bus_add_driver+0x98/0x220) from [] (driver_register+0x9c/0x13c)

[] (driver_register+0x9c/0x13c) from [] (do_one_initcall+0x90/0x164)

[] (do_one_initcall+0x90/0x164) from [] (kernel_init+0xf8/0x1b8)

[] (kernel_init+0xf8/0x1b8) from [] (kernel_thread_exit+0x0/0x8)

4 locks held by swapper/0/1:

#0:? (&__lockdep_no_validate__){......}, at: [] __driver_attach+0x40/0x8c

#1:? (&__lockdep_no_validate__){......}, at: [] __driver_attach+0x50/0x8c

#2:? (&card->mutex){+.+.+.}, at: [] snd_soc_register_card+0x274/0x10f4

#3:? (umhelper_sem){++++.+}, at: [] usermodehelper_read_trylock+0x4c/0xb8

adau1761 0-003b: Failed to firmware

zed-adau1761-snd zed_adau1761_snd.7:? adau-hifi 77600000.axi-i2s mapping ok

TCP: cubic registered

NET: Registered protocol family 17

VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

Registering SWP/SWPB emulation handler

drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

ALSA device list:

#0: HDMI monitor

#1: ZED ADAU1761

No connectors reported connected with modes

[drm] Cannot find any crtc or sizes - going 1024x768

Console: switching to colour frame buffer device 128x48

fb0:? frame buffer device

drm: registered panic notifier

[drm] Initialized axi_hdmi_drm 1.0.0 20120930 on minor 0

VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -30

Please append a correct "root=" boot option; here are the available partitions:

b300???????? 7639040 mmcblk0? driver: mmcblk

b301????????? 489274 mmcblk0p1 00000000-0000-0000-0000-000000000000

b302???????? 7149581 mmcblk0p2 00000000-0000-0000-0000-000000000000

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)

[] (unwind_backtrace+0x0/0xe0) from [] (panic+0x88/0x1e0)

[] (panic+0x88/0x1e0) from [] (mount_block_root+0x238/0x288)

[] (mount_block_root+0x238/0x288) from [] (prepare_namespace+0x160/0x1c0)

[] (prepare_namespace+0x160/0x1c0) from [] (kernel_init+0x178/0x1b8)

[] (kernel_init+0x178/0x1b8) from [] (kernel_thread_exit+0x0/0x8)

CPU1: stopping

[] (unwind_backtrace+0x0/0xe0) from [] (ipi_cpu_stop+0x3c/0x6c)

[] (ipi_cpu_stop+0x3c/0x6c) from [] (handle_IPI+0x68/0xb4)

[] (handle_IPI+0x68/0xb4) from [] (gic_handle_irq+0x54/0x5c)

[] (gic_handle_irq+0x54/0x5c) from [] (__irq_svc+0x44/0x78)

Exception stack(0xdcc77fa0 to 0xdcc77fe8)

7fa0: dcc76000 0001eaf0 dcc77fd8 dcc6e0c0 1cc6006a 00000015 10c0387d c06bcf54

7fc0: 0000406a 413fc090 00000000 00000000 00000000 dcc77fe8 dcc76018 c000e36c

7fe0: 20000013 ffffffff

[] (__irq_svc+0x44/0x78) from [] (default_idle+0x28/0x30)

[] (default_idle+0x28/0x30) from [] (cpu_idle+0x8c/0xe4)

[] (cpu_idle+0x8c/0xe4) from [<0039c134>] (0x39c134)

panic occurred, switching back to text console

今天終于發現了問題的所在，原來是SD卡在使用過程中不小心被鎖定了，SD卡處于寫保護狀態，將SD卡解鎖，上面的問題就解決了。而且還發現，SD卡處于寫保護狀態時，如果直接使用筆記本自帶的讀卡器訪問SD卡，則不可寫入；但是如果使用USB接口的讀卡器，則可以正常讀寫SD卡，而我們一直使用的是USB接口的SD卡讀卡器，所以之前沒有發現這個問題。

總結

以上是生活随笔為你收集整理的非cpu0启动linux,SD卡无法启动Linux的问题及解决的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。